The 40 most recent of 262 complaints, exactly as filed with NHTSA. These are owners' own accounts and have not been verified.
Nov 12, 2026 · FL
Power train
The contact owns a 2016 Ram 2500. While the contact's son was starting the vehicle, the gear shifter detached. The dealer was contacted and made aware of the failure. The contact was informed of an unknown recall with a similar failure; however, the VIN was not associated with a recall for the failure.
NHTSA ID 11777542
Nov 7, 2026 · OK
Unknown or other
Formal Complaint – Transmission Problems Following U61 PCM Recall Vehicle: 2016 Ram 2500 6.4L HEMI Transmission: 66RFE Mileage: Approximately 266,000 miles Recall: U61 – PCM Software Update Previous Calibration: 68259026AF Updated Calibration: 68259026AG To Whom It May Concern: I am requesting a formal investigation into transmission problems that began immediately after my vehicle received the U61 PCM software recall update at your Dodge dealership. I purchased this truck from Allen’s Used Cars and drove it for approximately two weeks without experiencing any transmission problems. Before the recall update, the truck shifted normally and had no check-engine light or noticeable transmission slipping. Immediately after the PCM update, I began experiencing the following problems: * Transmission slipping in 5th and 6th gears. * Engine RPM increasing without the truck gaining speed. * Sudden loss of pulling power. * Transmission slamming hard when the gear catches. * Diagnostic trouble code P0740. I returned to the dealership and was told that the PCM accepted the software update and that it installed correctly. However, the vehicle was never road-tested after the update. I understand that the vehicle has high mileage, but the transmission was operating normally before the recall service. I am requesting: 1. A complete transmission diagnostic. 2. Verification of the PCM calibration and software compatibility. 3. Investigation of the relationship between the PCM update and the transmission symptoms. 4. A road test with diagnostic equipment, if safe. 5. A technical assistance case with Stellantis. 6. A written explanation of the findings and recommended repairs. I am not asking anyone to assume responsibility without an investigation. I am asking that the sudden change in vehicle operation immediately following the recall service be taken seriously. Please document this complaint and provide a written response. Thank you.
NHTSA ID 11776389
Nov 4, 2026 · OR
Engine
Heater grid fell of got into motor had to replace the motor and fuel lines, injectors, and turbo. Cost me over 30K cash. My wife withdrew from her retirement so we could afford to replace the motor. Then I had to take a job and move to be able to pay the truck off.
NHTSA ID 11775735
Oct 22, 2026 · VA Crash
Air bags
I hit a deer coming around a corner at probably 45 mph, dead center in the middle of my bumper. My airbags did not deploy, and my front sensors did not alert me before collision.
NHTSA ID 11772878
Aug 31, 2026 · SC
Electrical system · Power train
I am reporting a transmission safety problem with my 2016 Ram 2500 Cummins that began shortly after FCA campaign U29 was performed. Before the recall work, the transmission and original solenoid were functioning normally. I had no transmission symptoms, warning lights, or transmission codes. The dealership performed U29 and replaced the transmission solenoid May 4-6, 2026. I picked the truck up May 6 at 149,091 miles. About 79 miles later, the check-engine light came on and transmission problems began. While driving, including on the interstate, the truck would suddenly jerk, the RPMs would rise quickly, and the truck would lose speed. On several occasions, traffic behind me had to react quickly to avoid hitting me. The dealership told me the solenoid installed during the U29 repair was defective and replaced it with another solenoid. The same problems continued. The truck later developed code P0871, became undriveable, and was towed back June 1. The original transmission ultimately failed. The dealership then installed a Mopar remanufactured transmission. I picked it up June 13. Within roughly 600 miles, it developed substantially identical symptoms and failure patterns, including P0870 and P0871, limp mode, and another major transmission failure. It was towed back June 24. The dealership later found the overdrive clutch had disintegrated and metal was present in the transmission fluid. The failed remanufactured transmission is now being handled under its Mopar warranty, and the dealership is looking to install a third transmission without identifying a clear reason for the repeated failures. I am concerned the same problem could happen again and believe the U29 repair, replacement parts, or another related transmission problem should be investigated.
NHTSA ID 11760982
Aug 25, 2026 · SC Crash
Power train
On August 25, 2026, my 2016 Ram 2500 was parked on private property. The driver states that she placed the automatic transmission in PARK before exiting the vehicle. After she exited, the unoccupied vehicle unexpectedly began rolling and struck a tree, causing vehicle damage. No one was injured. There were no known warning lights or messages indicating a problem before the incident. The cause has not yet been determined and the vehicle has not yet been inspected for this incident. The vehicle is available for inspection. This vehicle is equipped with a steering-column-mounted automatic transmission shifter. I am concerned that the incident may involve the transmission/shift interlock/Park system. I am aware of NHTSA Recall 17V-821 (FCA T79), involving unintended rollaway in certain Ram trucks, as well as NHTSA Recall Query RQ25003 concerning reported BTSI failures in vehicles including Ram 2500 models. The NHTSA VIN lookup currently shows zero unrepaired recalls for this vehicle; however, I do not yet know whether the prior T79 recall repair was performed on this specific vehicle or when it was performed. I did call the dealership and they said possibly 0ctober 3, 2018. I am submitting this complaint because the vehicle rolled after the driver reports placing the transmission in PARK and exiting the vehicle.
NHTSA ID 11759520
Aug 1, 2026 · TX
Steering
the V06 Recall on this vehicle that for some reason was approved is an inadequate repair. The steering wheel is not adjustable with the "Weld Fix". Stellantis should have to replace the defective parts. My truck is not not able to be aligned 100%. The repair was done in 2019, and I have complained about this in the past once I realized what they did to "FIX" the issue for the recall. They have been no help and said that because it was and approved repair even though this should never of been a long term solution.. according to them I'm SOL and the dealership can align it but other shops are saying that you can't truly align the car and steering with that fix in place. I would hope that you put pressure on them to make this right.
NHTSA ID 11754201
Jul 20, 2026 · AL
Steering · Suspension
This complaint is against HENDRICK CHRYSLER DODGE JEEP RAM IN HOOVER ALABAMA misaligned solid-axle geometry and compromised tire casings triggered a violent, uncontrollable oscillation through the steering system, rendering the truck an immediate highway safety hazard. The vehicle was so dangerous to operate that it could not be driven home and remains stranded at a secondary residential location. IV. EXPEDITION OF COMPLAINT: DEALERSHIP BAD-FAITH REFUSAL Following the failure, a corporate case file was officially opened with Ram Corporate Customer Care. Upon notification of the corporate escalation, the owner/general management of Hendrick Chrysler Dodge Jeep Ram in Hoover, AL placed a direct phone call to the consumer. During this conversation, the dealership owner explicitly and aggressively stated that the dealership would do anything they had to do to get out of fixing the mistakes made on the drag link, directly refusing to authorize a safe flatbed tow, refusing to replace the ruined, improperly welded linkage, and refusing to assume liability for the three structurally destroyed tires. REQUESTED REMEDIAL ACTIONS The complainant requests that the National Highway Traffic Safety Administration (NHTSA), the Federal Trade Commission, and the Alabama Attorney General's Consumer Protection Division launch an immediate investigation into Hendrick Chrysler Dodge Jeep Ram for faulty execution of federal safety mandates, reckless endangerment of motorists, and bad-faith commercial practices. The dealership must be held legally and financially accountable for: The immediate cost of a flatbed tow from the vehicle's stranded location to a certified repair facility. The complete removal of the ruined, welded steering components and the installation of Ram’s updated, factory-authorized non-welded, clamp-style drag link assembly. The complete financial reimbursement or replacement of three (3) structural tires destroyed as a direct consequence of the failed recall execution.
NHTSA ID 11751693
Jul 14, 2026 · WV
Electrical system
To Whom It May Concern, I am requesting a no-cost replacement of the factory Uconnect 8.4 radio in my truck (VIN: [XXX]) due to daily safety-related failures that significantly affect the safe operation of my vehicle. Every day, the radio experiences a startup delay where the screen remains black and many center stack functions are unavailable. This delay often lasts 5–10 minutes before the system becomes operational. During normal driving, the radio also displays repeated “Vehicle Phone Requires Service” error messages, creating a constant distraction that takes my attention away from the road. When these issues occur, the factory backup camera is unavailable. Losing the backup camera eliminates an important safety feature intended to help prevent collisions with pedestrians, children, vehicles, and objects while reversing. Additionally, the factory navigation and GPS no longer function at all. These are not minor convenience issues—they are daily safety concerns. Safety-related features should work immediately every time the vehicle is started. A factory infotainment system that fails every day, disables the backup camera during startup, and repeatedly distracts the driver while the vehicle is in motion presents an unacceptable safety risk. Because these failures occur daily and involve factory-installed safety equipment, I believe Stellantis should replace the defective Uconnect radio at no cost. I respectfully request that this complaint be documented and that a no-cost replacement be authorized. Thank you for your prompt attention to this matter. [XXX] VIN: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ID 11750226
May 26, 2026 · 97,000 miles · TX
Steering
The contact owns a 2016 RAM 2500. The contact stated while driving at an undisclosed speed, the steering wheel failed to steer in the intended direction. In addition, the contact stated that the steering wheel independently steered the vehicle to the right. The vehicle was taken to the dealer, however the contact was informed that the alignment could not be completed because of an unrepaired recall repair. The contact received a recall notification, NHTSA Campaign Number: 19V021000 (Steering). The vehicle was taken to the dealer, however the contact was informed that the recall repair was completed in July 2019. The vehicle was not repaired. The manufacturer was made aware of the failure but provided no assistance. The contact was informed that the recall repair was covered under warranty for two years from the date of completion. The contact stated that the recall repair was not performed, but marked as completed by the dealer. The failure mileage was approximately 97,000.
NHTSA ID 11740029
May 2, 2026 · NY
Service brakes · Electrical system
Electronic brake controller faulty
NHTSA ID 11735322
Apr 22, 2026 · CA
Engine · Power train
Grid heater nut/bolt detached and entered engine, causing catastrophic internal failure and total engine loss while driving.
NHTSA ID 11733046
Feb 17, 2026 · GA
Engine
Adding to form 11717793
NHTSA ID 11718528
Feb 14, 2026 · NJ
Unknown or other · Power train
Got into my truck after letting it warm up and the shifter broke out of the handle. It’s a known problem cause the design is flawed by putting so much pressure on the part. So in the end it breaks and then you can’t get your vehicle out of park or whatever gear it broke in. I was charged 718.00 for it to get fixed when I think this should be a recall or tsb.
NHTSA ID 11718053
Feb 13, 2026 · GA
Engine
The vgt actuator failed the truck only has 127000 miles on it ram extended the warranty for 2015 trucks but not 2016. The part to replace it from ram has almost doubled in a years time. It is now $2170. For this part whose internal computer components have failed. The files uploaded was just for the part. I can upload the repair cost when done. I am just trying to get everyone to see how corrupt these companies are becoming. They could have saved themselves some problems if they would just paid the $3000 to fix it this is a rough estimate.
NHTSA ID 11717792
Feb 12, 2026 · 113,000 miles · IL
Engine and engine cooling
The contact owns a 2016 Ram 2500. The contact stated that while driving at various speeds, the check engine warning light illuminated, and the vehicle lost motive power and went into LIMP Mode. The contact stated that the failure was intermittent but also occurred while towing a 30-foot trailer or a 24-foot trailer. Occasionally, after pulling over, turning off, and restarting the vehicle, the vehicle returned to normal functionality. On other occasions, the vehicle was towed back to the residence after the failure. The vehicle was taken to an Auto Parts Store and diagnosed using a handheld scanner, and a fault code associated with the turbo actuator for the diesel engine was retrieved. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The contact called a local dealer and was notified of Technical Service Bulletin Number: 09-005-22; however, the vehicle was not included. The manufacturer was informed of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 113,000.
NHTSA ID 11717651
Feb 9, 2026 · NM
Service brakes
ITBM Integrated Trailer Brake Module not outputting correct breaking voltage to trailer.
NHTSA ID 11716646
Jan 22, 2026 · TX
Steering
Drag link issue led to not being able to get an alignment, dealership and RAM support refused to fix it, as it was completed but they did not do it correctly the first time and it is dangerous
NHTSA ID 11712751
Jan 12, 2026 · MI
Steering
The low pressure power steering hose is leaking and can't get part for it. Been having to invest in tons of power steering fluid and want to know if this is gonna be a recall. It is very frustrating that we can't get parts for the problem.
NHTSA ID 11710332
Dec 30, 2025 · CA
Service brakes · Vehicle speed control · Electrical system
ABS FAILURE, WHICH TURNS OFF TRACTION CONTROL AND CRUISE CONTROL. This is a known issue for the HCU to fail. How is this not a recall on 2016 but it is on 17 and 18. Same parts.... have replace front hubs with new ABS sensors and rear ABS sensors, still on. It has to be the HCU or the module.
NHTSA ID 11707920
Nov 10, 2025 · CA
Power train
Incident Report – Gear Shift Failure Date of Incident: 11/10/2025 Vehicle: 2016 Ram 2500 Pickup Truck VIN [XXX] Mileage: [Insert Mileage] Location: [Insert Location of Incident] Description of Incident While attempting to shift the vehicle from Park (P) into Drive (D), the shift lever suddenly went limp and lost all resistance. Upon applying slight additional pressure to engage the transmission, the shift lever snapped off completely. The gear shift bracket—the component securing the shift rod—fractured in half at the point where the shift rod inserts into the bracket. This mechanical failure rendered the vehicle inoperable and unable to be shifted out of Park. No warning lights or prior symptoms were observed before the failure. The broken part was visually inspected and confirmed to be the shifting lever bracket, consistent with Mopar part number 68470756AA. Immediate Actions Taken The vehicle was safely secured to prevent unintended movement. Engine was turned off and keys removed. Visual inspection confirmed that the shift lever bracket had broken at the rod insertion point. Tow service was arranged for transport to a repair facility. Photographs of the damaged bracket and shifter assembly were taken for documentation. Assessment This incident represents a critical component failure of the gear shift mechanism, resulting in sudden loss of control over transmission operation. The break occurred under normal shifting force, indicating a possible material or design defect in the bracket assembly. Recommended Actions File a warranty or recall inquiry with Ram/Stellantis regarding potential defects in part 68470756AA. Replace the damaged bracket with a verified OEM replacement. Inspect surrounding linkage and cable components for stress damage or misalignment. Retain the failed part for potential recall or manufacturer investigation. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ID 11698580
Oct 13, 2025 · WV
Power train
I previously had recall 17V-821 work completed. This recall was for The Brake Transmission Shift Interlock (BTSI) locking pin may become stuck in the open position. I have the same issue now and see that NHTSA is investigating failed recall fixes. I have taken this to the dealer and an independent shop and am now trying to figure out how to get this repaired.
NHTSA ID 11693040
Sep 29, 2025 · 238,000 miles · TX
Power train
The contact owns a 2016 Ram 1500. The contact stated that the shift solenoid change message was displayed. The vehicle was taken to the local dealer for a recall repair. Upon retrieving the vehicle, the vehicle failed to shift and had no power. The vehicle was diagnosed with a faulty shift solenoid. The replacement parts were on backorder. The local dealer later informed the contact that the transmission was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was contacted and filed a complaint. The manufacturer declined to cover the cost of the repair. The failure mileage was approximately 238,000.
NHTSA ID 11690345
Sep 19, 2025 · GA
Unknown or other
The grab handle or left interior a arm part broke and fell of in my lap while I was driving luckily it did not fall off when I entered the vehicle or I would have been flat on my back. I contacted Stelantis got the typical run around. Tried to order new part but part has been discontinued. Now I am driving with airbag not covered and exposed. The part number for my truck is 5RM911XAC you can check discontinued. I ask Stelantis to find part after I tried for months to no avail. Reply was sorry part discontinued. What broke was the plastic that holds two screws in. Hopefully no one gets hurt if others break. In my opinion it seems like a bad design to save money. The replacement part by the way is $313.00 for plastic with leather wrapped handle. I was willing to spend that but the attitude I got from Stelantis was very non caring after I spent $60,000 on a truck in 2016. I ordered this part in May of 2025 then in August they told me it was discontinued.
NHTSA ID 11688411
Jul 14, 2025 · FL
Power train
Transmission gear selector lever can be moved from park to reverse, neutral, and drive without having the brake pedal depressed. This is the way the transmission gear selector currently operates. This is not a one-time incident. I bought this vehicle recently and noticed this transmission gear selector lever issue about a month ago.
NHTSA ID 11673363
May 29, 2025 · UT
Engine
Towing my trailer with my 2016 Ram 2500, at 48,000 miles I experienced complete turbo failure in heavy traffic at highway speeds. Power was reduced to minimums causing hazardous conditions. The "check engine" light illuminated. I maintained control and eventually had the codes scanned at both a local auto parts store and Larry Miller Dodge/Ram in Sandy, Utah. The codes identified were for the turbo actuator/turbo. Larry Miller said they could replace the actuator, but I'd be back in three weeks for the turbo replacement as well. They were three weeks out for labor. I contacted a local diesel repair shop who purchased the turbo and actuator from Larry Miller Dodge Ram and had it installed in a day. Subsequent to these repairs ($5,400.00) I have learned that MOPAR issued Warranty Bulletin D-22-06, dated March 16, 2022, for the same make and model as mine, only for the year 2015. My truck was built in 2015 and the parts and computer codes for failure are identical. This published warranty bulletin issued relief of a new extended warranty of 15 years /150,000 miles for the installed turbo actuator/turbo. Since mine failed at 48,000 miles, this could be a continuation of the aforementioned issue with the stated 2015 year failures. I was lucky I didn't create a traffic accident when this turbo system failed since it was sudden and violent when the loss of power occurred without warning. I'm asking you to probe or look at the facts that the issue with these Garrett turbos are still outstanding whether Doge/Ram/Fiat/Mopar wants to include them in their campaign. The danger is real. The costs to retired people, such as myself, is consequential and devastating. It is unfair there is no way of sending queries to the manufacturers to alert them of this condition. The only way to communicate is to talk to a person in India and the communication barrier is tremendously difficult as is the chance of getting any return on the days and weeks of attempts for resolution.
NHTSA ID 11663742
May 28, 2025 · CA
Engine · Power train
It is the Water pump We have the Concentric brand with out a vent hole picture attached ( which is the one under recall but doesn’t come up on our vin) Yes A Mechanic No No
NHTSA ID 11663422
May 22, 2025 · MA
Steering · Suspension
I received an NHTSA recall notice V06/NHTSA 19V-021 on or about April 2023, I brought this vehicle to Stat Line Jeep Dodge RAM located in Somerset, MA early April to fix the vehicle pursuant to the recall notice for a Drag Link problem/defect. Upon arrival the service department stated they had not received a welding machine necessary to fix the problem and to call for another appointment, On or about April 10, 2023, I again brought the vehicle to State Line RAM dealership to complete the repair. On May 31, 2023, I brought the vehicle to Town Fair Tire Center to have all 4 new tires replaced and have the front end aligned. I was told that the alignment could not take place since the dealership welded the "Tie Rods" together. I brought the vehicle back to State Line dealership and asked why my vehicle's tie rods were welded. They told me that the NHTSA had told them that was the fix. I wanted to know how to get the vehicle aligned and the dealership told me that I would have to pay $850.00 to replace them and that should have been done except the NHTSA said to weld them together.
NHTSA ID 11662561
Apr 18, 2025 · TX
Service brakes · Fuel/propulsion system
Def system failed ABS, track,tire pressure. Service 4 wheel drive system. 4 wheel drive system temporarily unavailable.
NHTSA ID 11655557
Apr 6, 2025 · MN
Engine · Fuel/propulsion system
The service engine lamp came on. When the mechanic investigated, it was determined that the problem is identical to the Warranty Bulletin titled Cummins 6.7L Turbocharger Actuator - X99 Warranty Extension that pertains to the 2015 RAM 2500 pickup. My vehicle is a 2016 and there is no warranty extension, even though it is an identical problem. The vehicle was not drivable as is and I had to replace the Turbocharger Actuator. I am assuming that this is a known problem to Cummins and to RAM. There should be a Warranty Bulletin for the 2016 also.
NHTSA ID 11653069
Feb 4, 2025 · 17,519 miles · MA
Steering
The contact owns a 2016 Dodge Ram 2500. The contact stated that the vehicle was included in NHTSA Campaign Number: 19V021000 (Steering) and the vehicle was taken to the dealer for the recall repair. The contact stated that the vehicle was taken for an alignment and the contact was informed that an alignment could not be completed because to the tie rods were welded together. The dealer who performed the recall repair was contacted and confirmed that the tie rods were to be welded as stated in the recall. The dealer informed the contact that the repair was approved by the NHTSA and that for the alignment to be performed, the entire part had to be replaced. The vehicle was not repaired. The recall repair stated that Chrysler would notify owners, and dealers would check the steering linkage jam nut tightness, replacing the drag link assembly or welding the nut to the adjuster sleeve, free of charge. The contact believed that the dealer failed to perform the remedy due to the tie rods not specifically being mentioned as what was expected to be welded together. The manufacturer was made aware of the issue and confirmed that the remedy was to weld the tie rods. The manufacturer opened a case regarding the failure. The failure mileage was 17,519.
NHTSA ID 11640592
Jan 15, 2025 · MO
Seat belts · Air bags · Wheels
Contacted FCA Recall Assistant Center on 10/23/2024 and filed a complaint against Corwin Chrysler Dodge, 3306 E. Kearney St., Springfield, MO., 65803 regarding Safety Recalls that Corwin Chrysler Dodge fraudulently checked off in the system as fixed, but they were not fixed. Case# [XXX] was assigned to the complaint. Keith is the assigned CS Manager and can be reached at 844-378-0575, ext: 3124. Keith informed us today that his hands are tied at this time and he doesn't have the authority to uncheck the safety recalls in the system that would be up to the dealership Corwin Chrysler Dodge in Springfield, MO. As of today, January 15, 2025, we still do not have resolution to this issue. We were informed to reach out to James River Dodge RAM, Ozark, Missouri. List of recalls below that we are aware that were completed by Corwin Chrysler Dodge of Springfield, Missouri. 1. Water Pump Recall T51 (Corwin Chrysler Dodge completed) 2. New Tailgate Latch U74 (Corwin Chrysler Dodge completed) We spoke to David, Service Manager, on 10/25/2024 and was informed since the system shows everything regarding the safety recalls for this vehicle are checked off in the system as fixed by Corwin Chrysler as completed. David told us that the safety recalls in the system that are showing fixed would need to be unchecked in the system in order for his team to recheck all the recalls on this vehicle and get paid for the service, because Corwin was paid for fixing the safety recalls when they checked them off in the system. 1. Steering - Drag Linkage Welded V06 (James River Chrysler could visibly see this was completed (10/25/2024) 2. Truck Engine Recalibration 67A (James River Chrysler completed on 10/25/2024) No other recalls to the best of our knowledge have been fixed on our 2016 RAM, Dodge Laramie 2500, 6.7L, Diesel Motor, vehicle. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ID 11636143
Sep 13, 2024 · 137,804 miles · TX
Tires
The contact owns a 2016 Ram 2500 equipped with Hankook Tires, Tire Line: Dynapro AT2, Tire Size: 275/70/R18, DOT Number: 1BJWBRNB. The contact stated that while his son was driving approximately 60-65 MPH, the vehicle started severely vibrating and shaking on the front passenger’s side of the vehicle. The driver pulled to the side of the road and removed and replaced the front passenger’s side tire with the spare. The vehicle was driven to Discount Tire where it was diagnosed that there was a bubble on the tire. The vehicle was taken to Walmart where the tire was replaced. The contact stated that approximately 3 months after replacing the tire, the driver’s side rear and driver’s side front experienced the same failure. The contact continued to drive at speeds lower than 20 -25 MPH. The dealer was not made aware of the failure. The manufacturer was not made aware of the failure. The vehicle failure mileage was 137,804, and the tire failure mileage was 23,000.
NHTSA ID 11614360
Sep 7, 2024 · SC
Power train
I have a 2016 Ram 2500 Power Wagon that i have turned into a show truck. The truck has never been off-road or in the mud, it is driven to and from the shows. Last [XXX] as i was driving to Hickory, NC for a car show on Saturday August 31st my truck instantly lost power and turned on the engine light. The transmission felt like it was stuck in second or third gear, so i pulled over and scanned the PCM to see what the DTC code and it came back as P0870. Went online to research the code and see what it had to say about it and it stated to clear the code to see if it comes back on which i didn't. The light has not returned as of yet but when the truck hits overdrive it has a high pitch squeal coming from it meaning the transmission. I brought it in to my local dealership on Wednesday September 4th to have it looked at they performed DIAG and CVI inspection to find the transmission is starting to fail internally recommend replacing the transmission. Now want me to pay out of pocket for a new transmission even though i have max care warranty on the truck when i bought it new. i don't have $6000.00 to pay for a new transmission that's on back order. If it comes down to it and i have to get my neighbor to help me get the transmission out of this truck cause I'm [XXX] then i will rebuild it my [XXX] thing myself before i pay them $6000.00. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ID 11613233
Jul 16, 2024 · CA
Steering · Service brakes
Some time as i apply the brakes i get a pulse pushing back on the brake pedal , it results in a slower braking action . Also i have a power steering fluid leak coming from the brake booster system . The brakes and the power steering go through the same system . The brake problem has been happening about a year and the power steering leak at the booster about 2 months
NHTSA ID 11602722
Jul 15, 2024 · OR
Steering
On 7/11/2024, I had a service performed at a local independent automotive repair facility because I purchased new tires for the truck. The repair service history on the truck was limited because I inherited this vehicle from my deceased son. I intend to transfer ownership to my other son who will be towing a large RV Trailer with it. Prior to this service, I was unaware of an important safety recall identified as V06 Drag Link. After the alignment service was completed, the local service technician explained he was able to perform the alignment and confirmed the V06 repair had been previously done. He said the steering box nuts on each end of the Adjuster Sleeve had been welded, which was the recommended fix presented in the FCA US LLC safety recall notification. The truck steering wheel was not centered since I acquired it in 2021. At times it was cocked to the left between the 11/12 o'clock position. I attributed this to the well worn tires not knowing about the V06 safety recall issue. The service technician advised that while doing the alignment he noted the welded adjuster sleeve "had play" in it and recommended I take the vehicle to an authorized RAM dealership for this issue because he stated "an updated sleeve" was made available subsequent to issuance of the V06 safety recall notification. He warned a potential failure of the adjuster sleeve could result in loss of steering and a crash. I followed the service technician advice and took the vehicle to the local RAM dealership. I presented the alignment service finding to a management official who responded the recommended safety recall issue had been fixed and no updated sleeve available. The manager never offered to inspect the adjuster sleeve "play" issue and proceeded to list over $3,000 of other 60,000 mile recommended services. Because of the potential safety issue identified as described, I am deeply concerned the RAM dealership was intentionally discarding my safety concerns.
NHTSA ID 11602340
Jun 11, 2024 · MA
Service brakes, hydraulic · Electronic stability control (ESC)
The contact owns a 2016 Ram 2500. The contact stated that while driving at an undisclosed speed, the ABS warning light illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the ABS control module. The vehicle was repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 22V140000 (Service Brakes, Hydraulic, Electronic Stability Control), but the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was unknown. The VIN was not available.
NHTSA ID 11593664
May 28, 2024 · WA
Engine
It is known that the 2016 Ram crew cab 4x4 has exhaust leak problems. The bolts on the exhaust manifold will break and exhaust will escape the manifold causing extra heat to flow into the engine bay, and fumes to enter the cabin of the vehicle. carbon monoxide is colorless and orderless and causes headaches, nausea, dizziness, and even death if inhaled. The exhaust manifold leaks must be fixed.
NHTSA ID 11591048
May 28, 2024 · WI
Service brakes · Electrical system
My ABS lights is on causing my cruise control to not be functioning. When I first start the vehicle, i get a message to "service electronic brake system." I have new brake pads with rotors and still have this message.
NHTSA ID 11590973
May 22, 2024 · 50,000 miles · PA
Steering
The contact owns a 2016 Ram 2500. The contact stated while the vehicle was taken for an alignment, the independent mechanic became aware that the steering linkage was loosened. There was no warning light illuminated. The vehicle was not repaired. The vehicle was previously repaired under NHTSA Campaign Number: 19V021000 (Steering); however, the failure reoccurred. The manufacturer was made not aware of the failure. The failure mileage was approximately 50,000.
NHTSA ID 11590122